>>>Links: Construction Points and Acceptance Notices for Door Covers and Window Covers
1. The structure of the door frame and window cover is used for the closet of the wardrobe or other large material corners. After the nail is finished, it is corrected with a square. After the hammer and the horizontal side, it is fixed with a wooden pad and then fixed. Must be 10-20mm above the ground level to prevent water and mildew.
When making the door and window cover line structure, it should be opened according to the line width with a 9-PCT plate, and the width should be narrower than the line width by 5-6mm, and it should be fixed to the front of the door and window cover. The vertical deviation of the door pocket is more than 2mm. The woodworking team leader must be reworked and the foreman must pay a fine of 30 yuan. Below the door line, the nine-percent board above the door line, the carpenter must be reworked, the foreman fined 30 yuan. If the PCT board cannot cover the gap between the door cover and the wall, then the paperboard gypsum board must be used to seal the gap before the nine-ply board is nailed and then the nine-clamp slats are nailed. Where the uncovered gypsum board was found, the carpentry team made a long-range attack and compensated the materials. The foreman had a fine of 30 yuan.
2. Door leaf: According to the height of the door hole, consider the thickness of solid wood floor, composite floor or floor tile and expansion joint strip; leave a good gap, ensure that the floor is 5-8mm after installation, the door edge seam is 3mm, and the door leaf thickness is guaranteed at 42. -46mm. If the gap below the door is 5-8mm, if the door is seamed more than 3mm, the work must be reworked and the materials must be compensated. The foreman shall fine a fine of 30 yuan, excluding the plastic steel doors.
1 Flat door: Daxin slats are used as keel, skeleton is opened 60mm with large core board, double-sided dislocation slot, distance between slots is 150mm. Daxinban horizontal clearance distance of 200mm, the interface gap is not more than 1mm, double-sided paste quality two-story three PCT board, and then do the mixed paint on both sides, without lines shut, such as the decorative type, double-sided paste three PCT board decoration panel. Reinforce the lock on the mounting locks and hinges (300 x 250 x width). If it is found that the large core board is laid flat, the rework material is taken up by the woodworking team leader and the foreman will be fined 30 yuan. If the door lock is found and the door hinge is not dense, the foreman shall be fined 30 yuan; if the paint door is found mixed The closing line closed, the woodworking team leader paid compensation materials, and the foreman was fined 30 yuan.
2 glass doors:
Daxin board made keel, two large core board flat, double-sided pressure two layers of three PCT board, the surface of the plywood dug out the entire glass position, and then do the paint on both sides, without lines shut (nitro-clear varnish after scratching Putty). If it is found that the three PCT boards are not hollowed out, the woodworking team leader will make compensation for the materials and the foreman will be fined 30 yuan. If the board is to be put sideways, the foreman will be fined 30 yuan. If he is found to have closed the line, the foreman will be fined 30 yuan. The front face of the middle pressure glass is pressed with a three-ply plate to hold the line to ensure that no gap is visible on the front. If it is not done according to this method, the carpenter team leader will rework and the foreman will be fined 30 yuan. Where the lines are interfaced by male and female methods.
3 double-sided convex door: a, mixed paint type: base large core board, convex 12% slat fight.
b, varnish finish type: base large core board, convex surface for nine percent slats, the underlying veneer surface.
Some bumps are based on the design.
>>>Links: Door Door Making Process
3. The method of pressing the door is the same as the method of pressing the door.
4. Locks and metal hinges of the door should be drilled and installed before painting, and removed when painting. After the paint is finished, it is finally installed and fixed. If the door locks and hardware hinges are not removed after painting, the foreman will be fined 30 yuan for each item.
5, kitchen door in considering the overall design results, will use wooden doors, bathroom door width should not be less than 600mm, consider the waterproof requirements are to use moisture treatment (sometimes use fire board veneer, the corresponding plastic lines closed mouth), The bottom of the door socket, veneer, and lines are above the ground level and are protected from moisture. If you fail to do it according to the regulations, a fine of 30 yuan will be required.
6, sash: structure for the three nine PCT board slot (spacing 300mm) and uniform dislocation press, such as mixed paint type, double-sided whole plywood hollowing, do not close lines, double-sided paint. Such as lacquer veneer type, double-sided decorative panel spell angle, the corresponding flat line edge. If you fail to do it according to the regulations, a fine of 30 yuan will be required.
7, all the decorative materials must be done without partial color, seam filling smooth, straight, fight square Founder. The edges of the lines are also smooth and flat, and the lines are seamless in their spelling angles. Lines and veneers are seamless. If the color of upholstery panel door is not correct, the compensation for the group leader shall be fined by 30 yuan. If the color of the swatches between the front line and the cabinet door is too different, the group leader shall compensate the material and the foreman shall be fined 30 yuan; if the same cabinet is in line Differently, the leader of the compensation materials, the foreman fined 30 yuan.
Renovation Carpentry knowledge Carpentry Furniture Three trees Lacquerwork Windowpanes Glass Doors Glass bricks Glass doors Doors Doors Flooring tiles Glass Doors Doors Doors Design Toilets Watertight Integral bathroom Bathroom doors
Angle valve
Angle valve used in every place if need install faucets. It is a fitting, which connect between water plumbing and faucet`s flexible hose. Most of these made of Brass and chrome finished. Some made of stainless steel. Ceramic cartridge, quality can guarantee ten years no leakage water and no rusty.
Angle Valves,Brass Angle Valve,Angle Seat Valve,Angle Globe Valve
SHENZHEN KING OF SUN INDUSTRY CO.,LTD , https://www.handyfaucets.com