The doors and windows in the house should be the most frequently used and the most vulnerable part of many furniture. However, if the owner can skillfully carry out the doors and windows and use and maintenance in the usual time, it can extend the use time of the doors and windows. Then, let Xiaobian introduce some tips for the use and maintenance of related doors and windows.
Daily maintenance of aluminum alloy doors and windows
1 Aluminum alloy doors and windows in normal use, the action should be light, push and pull go with the flow; if you find that there are difficulties, do not hard pull hard push, should first eliminate the existing faults. Ash accumulation, deformation is the main reason for the difficulty of pushing and pulling of aluminum alloy doors and windows, to keep the door frame clean, especially to keep the position of the door and window sliding slot clean. A large amount of dust can be removed from the inside of the tank and inside the door seal by using a vacuum cleaner.
2 When cleaning aluminum alloy doors and windows, people should not step on the aluminum frame as much as possible, and do not hold the frame as a human support.
3 Aluminum alloy doors and windows can choose to use a soft cloth dampened with water or a neutral detergent, do not use ordinary soap and washing powder, but also can not use detergents, toilet detergents and other strong acid and alkali cleaners.
4 After the rainy day, the wet glass and door and window frame should be wiped out in time, paying special attention to drying the chute. The chute is used for a long time, the friction is increased, and a little oil or a layer of fire wax oil can be added.
5 Always check the joints of the aluminum alloy frame, tighten the bolts in time, and replace the damaged parts. Loosen the vulnerable parts of aluminum alloy doors and windows such as shaft pins, wind braces, and floor springs. Always check them regularly and keep them clean and flexible.
6 Sealing tops and glass seals are the key structures to ensure the insulation of doors and windows. If they fall off, they should be repaired and replaced in time.
7 Always check the joints of the aluminum alloy frame wall. If it is loose for a long time, it will easily deform the whole frame, so that the doors and windows cannot be closed and sealed. Therefore, the loose screw at the joint should be tightened immediately. If the base of the screw is loose, apply a small amount of cement to seal with a strong epoxy glue.
Daily maintenance of plastic steel doors and windows
The comprehensive performance of plastic steel doors and windows is the same as that of aluminum alloy doors and windows, and the maintenance requirements are the same as those of aluminum alloy doors and windows.
However, plastic steel doors and windows are resistant to acid and alkali, and can be cleaned with ordinary detergent such as soapy water, but the surface of plastic doors and windows is not rubbed, especially pay attention not to scratch, do not get contaminated with gasoline and banana water. Also prevent exposure to boiling water and contact with high temperature deformation. During the use and cleaning process, the bottom frame of the doors and windows should not be pushed and hit with hard objects such as knives and hammers.
In addition to the daily maintenance after the installation is completed, Xiao Bian reminds everyone that it is necessary to check after installation. According to the recommendations of the professional home improvement project manager, the following five aspects are generally required after the door and window are installed:
A. There is no crack in the weld of the profile of the door and window frame and the fan.
B. Whether the door and window sash has obvious deformation, warpage, and flat fan sag.
C. Check the seal strip and the strip for shrinkage, deformation and clearance.
D. Whether the hardware accessories are broken, damaged or tight.
E. Is the drain hole unobstructed?
Concerned about surprises
Label: Different materials door and window maintenance skills
Previous: Combination of safety valve and rupture disc installation and application conditions Next: What are the materials of the wardrobe door
Product categories of Corrugated Sheet Roll Forming Machine,we are specialized
manufacturers from China,Corrugated Sheet Roll Forming Machine,sheet rollforming machine,
suppliers/factory,wholesele high-quality product of Corrugated Sheet Roll Forming Machine,
R & D and manufacturing , we have perfect after-sales service and technical support . Look forward
to your cooperation !
Corrugated Sheet Roll Forming Machine
Corrugated Sheet Roll Forming Machine,Trapezoidal Sheet Roll Forming Machinery,Color Steel Sheets Roll Forming Machinery,Color Steel Panel Roll Forming Machinery
BOTOU HUATONG CORRUGATED MACHINERY MANUFACTURING CO.,LTD , https://www.htrollforming.com