I. Daily maintenance and maintenance 1. Regularly clean the leaves, waste paper, rags and other garbage in the pool to keep the pool clean. 2. Regularly check whether the wiring in the electric control cabinet is loose, and periodically remove dust from the internal electrical components. (Recommended every six months.) 3. When the equipment is deactivated for a long time, it must be arranged, routinely maintained and maintained. 1. Regularly clean the leaves, waste paper, rags and other garbage in the pool to keep the pool clean. 2. Regularly check whether the wiring in the electric control cabinet is loose, and periodically remove dust from the internal electrical components. (Recommended every six months.) 3. When the equipment is deactivated for a long time, the accumulated water in the pipeline must be excluded. It is recommended to drive the pump at least once a day for 3-5 minutes to protect the service life of the pump. The debris filter of the filter pump is cleaned regularly (it is recommended once a week, depending on the actual conditions of the pump working pressure). Second, maintenance and maintenance procedures (A) disinfection and water treatment system operation: the use of fiber filter: When the pressure gauge of the filter increases, until the pressure value of the cleaning, you need to clean, otherwise the filtration effect is not good. Depending on the water quality conditions, the fiber filter can be cleaned and used several times before replacing the new one. The pressure gauge value when using the new net must be recorded and will vary depending on the size of the tubing used. When the pressure rise is greater than 0.7 kg, cleaning is required. Disassembly and cleaning of the filter: Stop the pump, open the drain valve and bleed valve, and close the other valves. Open the V-shaped clamp (between the fixed cylinder and the cover) to remove the cylinder head. Loosen the wing nut, remove the washer and round gland, and remove the fiber filter. Replace or clean the filter. Install the new net or the cleaned filter on the multi-tube, put the circular gland, and tighten the wing nut with the washer. The butterfly nut should only be properly tightened, and do not use iron. Cleaning, seals, and the seal wall and seal ring that the seal contacts. Install the filter according to the reverse process of disassembly. (2) Use and replacement of underwater lights: 1. Fill the pool with water. The underwater light is 300W/12V safe voltage. Do not energize the underwater light before the underwater light is completely immersed in the water. The pool surface is not over water. After turning off the lights, turn on all power switches or line protection circuit breakers to check if the equipment is working properly. 2. Only change the wick of the underwater light to close the main electric breaker or circuit breaker. ----The electric brake is only used for the underwater light itself. The following conditions should be met when replacing. 2.1 A new lamp lens washer 2.2 an appropriate power The reflective wick has a new cap gasket installed whenever the lamp is removed. If it is not replaced, water will seep into the equipment, causing equipment damage. Remove the lamp fitting, remove the screw on the surface, remove the wick, and place the accessory on the shore. Remove the fixture and bulb, remove and discard the old gasket. To install a new gasket, in order to ensure the sealing, when installing the guide screw, it must be tightened as shown in the figure. 2.2.1 When the surface of the lamp housing is chrome-plated or brass, first adjust the position of the clock 12 points to the screw, then set the clock to 6 o'clock. Reinforce the screws in the position and reinforce the screws in other positions. Through the above sequence, all the screws are reinforced step by step until all the screws are smoothly and safely reinforced. 2.2.2 The surface of the lamp housing is stainless steel "target=_blank> stainless steel, the lamp is placed on the base, and the gasket is placed on the top of the lamp housing. Each time you reinstall, you must replace the new gasket. =_blank>The stainless steel ring is placed in the center position and placed on the mounted lamp body and washer. With the curved back of the ring card down, unfold the card and place it in the groove of the pole. Check that the card is properly connected to all the fixing rods. Turn the lamp body so that its lamp head is down. Reinforce the screws and nuts until the rear of the ring is no more than 1/4 inch. After doing the above, place the lamp in the wall hole and reinforce it with special stainless steel "target=_blank> stainless steel screws. Contact: Wu Zeming Tel: +86-02066621771, Fax: +86-02066621771, Mobile Phone, Electronics Email: [email protected], URL: http://, above keywords: spa pool project, spa equipment, pool pump, pool filter, pool project, spa pump, massage pump, pool equipment maintenance, swimming pool Underwater lights http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Product categories of Plastic Cutting Board, we are specialized manufacturers from China, Plastic Cutting Board, Chopping Block suppliers/factory, wholesale high-quality products of Plastic Cutting Board R & D and manufacturing, we have the perfect after-sales service and technical support. Look forward to your cooperation!
Plastic Cutting Board
Plastic Cutting Board,Plastic Chopping Board,Large Plastic Cutting Board,Plastic Cutting Board Sheets
Yangjiang YJCB Trade Co., Ltd , https://www.cbprokitchen.com