Means one: wall paint
Steal workers index: ★ ☆
Phenomenon: Latex paint is the most common wall decoration material at present. In concrete construction, it can be painted, rolled or sprayed. For interior decoration of a room, general latex paint needs to be coated twice or more to qualify. If the workers are not serious or perfunctory during the construction, there will often be color differences, especially with darker emulsion paints.
Experts advise: Before the use of latex paint to add a certain amount of water, deployment of a good latex paint to run out. Paints of the same color are also best painted once. If the wall needs to be repaired after construction, the whole wall should be repainted again.
Means two: sewage pipeline
Steal workers index: ★ ★
Phenomenon: A friend who has had construction experience, has encountered such a situation: the construction is completed, on the surface it seems that there is no problem in the renovation project, in full compliance with their own requirements, but once the acceptance is completed, but found the kitchen and bathroom Poor water? In fact, this is caused by the construction team cutting corners in the project. In order to save time and money, a few construction teams may pour concrete blocks containing a lot of cement and sand directly into the sewers. This will cause poor drainage pipes in the future. problem.
The expert reminds: We must strictly supervise and remind the construction team in advance that we cannot use the sewer as garbage road. After the construction of the waterway is completed, all the basins, basins and bathtubs are filled with water to see if the water is unobstructed and if there is any leakage of the pipeline. After all these steps have been completed, acceptance can be considered.
Means three: wire connector
Steal workers index: ★ ★ ☆
Phenomenon: This is also a very stealthy jerry, usually after the completion of the renovation, after the completion of the renovation, consumers in the use of electrical appliances, especially some of the more power-hungry water heaters, air conditioners, etc., switch, socket fever Even burned, some inexperienced consumers often think that this is caused by high-power electrical appliances. Actually, this is not the case. In such a situation, it is very likely that electricians do not follow construction requirements when installing sockets, switches and lamps. Caused by wiring.
Experts remind that summer is coming again, and the use of high-power electrical appliances such as air conditioners is inevitable. Therefore, construction must be supervised by electricians in strict accordance with the operating procedures. After all switches and sockets are installed, it is necessary to carry out the actual work. The use of these parts to see if there is fever, in order to prevent the subsequent use of electrical appliances in the process of causing unnecessary losses.
Means four: wall tile paving
Steal workers index: ★ ★ ★
Phenomenon: Paving tiles is a technical job. If the workers cut corners, it is easy to see problems such as hollowing of the tiles and misalignment of the joints. This will not only reduce the overall aesthetics of the home, but also cause the tiles to crack and crush. In addition, there are also particular concerns about cements and adhesives used for paving tiles. If the mix ratio is unreasonable, there are problems such as falling off.
Experts advise: Wall tiles should be flat and solid, clear patterns, no dirt and grime marks, the surface color is basically the same, uniform joints, plates without cracks, drop angles and lack of edges, the local hollowing shall not exceed 5% of the total.
Means 5: Wall ticking
Steal workers index: ★ ★ ★ ☆
Phenomenon: Today's home renovations generally choose to bury underground pipelines in order to maintain the simplicity and safety of the living environment. To bury underground pipelines, it is necessary to grooving walls and floors before embedding. A few workers perform barbaric construction during slotting operations, which will not only damage the building load-bearing structures, but also cause damage to other nearby pipelines.
Experts advise: Before construction, we must reconfirm the direction and location of the pipeline with the construction team leader. For different wall structures, the requirements for slotting are not the same: the walls of the load-bearing wall in the house are not allowed to be slotted, and the wall with the insulating layer is easy to cause cracking on the surface after being slotted, and on the ground Slotting, but also be careful not to damage the floor, causing trouble to the residents downstairs.
Means six: seam modification
Steal workers index: ★★★★
Phenomenon: In places where walls meet doors and windows, and where two different colors of paint are docked, it is not easy to be noticed. Therefore, these places are exactly what the workers often perfunctory. You often see mixed paints between latex paint and wood, and various problems at the joints.
Experts advise: The treatment of joints is very important, you must supervise the workers to seriously construct. If there are two colors of paint on the wall facing each other, it is necessary to apply adhesive tape on the edge of the first color during construction, and then apply another color of paint on it, so that the construction is completed. After tearing off the tape, the entire seam can be very neat.
Means seven: wire wear tube
Steal workers index: ★★★★☆
Phenomenon: In home renovation construction, almost all the wires are worn in PVC pipes and buried in the walls. Therefore, after the electric wires were put into the PVC pipes, consumers couldn't see them at all, and they could not pass the inspection and acceptance. If the worker is not careful in the operation, it will cause the wire to kink in the tube, causing electricity hazards. If workers deliberately cut corners, they will use wires with joints or put several wires in the same PVC pipe. If problems occur, it will be difficult to replace them.
Experts advise: Consumers are advised to purchase their own wires, then supervise workers' operations at the site, and conduct power-on tests after installation. In addition, consumers must allow the decoration company to leave a "pipeline map." When the electrician had just buried the wires in the wall, he could number the walls and draw a floor plan. Then he used the strokes to draw the direction of the wires and the specific location of the wires, indicating the position on the floor, the ground and the adjacent wall. In particular, the position of the joints of the pipelines should be marked so that in the event of a fault, the line position can be found immediately.
Means eight: facet processing
Steal workers index: ★★★★☆
Phenomenon: The so-called “small face†is a small place that some consumers can't see but does not pay much attention to, such as the upper edge of the door, the underside of the window sill, and so on. Some workers here will cut corners and materials, or even not. Do any processing.
Experts advise: Always keep in mind that there are 6 planes for any object. Don't ignore any details when checking the quality of the project.
Means 9: Ground Leveling
Steal workers index: ★★★★★
Phenomenon: In some projects where there is a suspicion of cutting corners, it is often found that there is a phenomenon of tilting at the edge of the wooden floor of the home, especially near the corners of the wall. What causes this problem? An important reason for wood floor tilting is due to problems with floor leveling before laying. Because some houses are not well-grounded, they need to be re-leveled before laying the floor. If the workers are not careful or deliberately rigged, it will cause “more and more inconveniencesâ€, posing a hidden danger to the floor tilting in the future.
Experts advise: Before ground leveling, ground surface treatment must be done first, and then use cement mortar to level the ground. After the cement is dry, determine the flatness of the entire floor using a dedicated level ruler, and then proceed to the next step.
Means 10: Substrate Treatment
Steal workers index: ★★★★★
Phenomenon: Before painting latex paint and paving the wall and floor tiles, we must do a good job on the surface treatment of the wall or the ground. For the new house, the substrate treatment generally only needs to be polished with coarse sandpaper, and it is not necessary to eradicate the original paint layer. However, the walls of ordinary old houses need to be removed before the next process can be carried out. Some workers, due to the lack of knowledge of the householder about the knowledge in this area, are cutting corners in this area during construction. The consequences of this situation are that unevenness of the wall is caused, there is a color difference after the paint is applied, and the emulsion paint is discolored. Cracks or even peeling, or tiles stuck loosely.
Experts advise: In the construction of paving tiles, you should pay attention to the fact that ceramic tiles cannot be laid directly on the surface of lime mortar, lime paste, lime plaster, hemp plaster and latex paint. Can be laid. Bonding pastes used between tiles and substrates should be formulated in strict accordance with the construction standards and proportions, using the specified grades of cement and adhesive materials, and they cannot be randomly deployed. When applying latex paint, you must pay attention to whether the shading of the wall putty is even and smooth, whether the sanding and rolling are in place. In addition, you should pay attention to whether the latex paint is properly proportioned and whether there is excessive water.
Steal workers index: ★ ☆
Phenomenon: Latex paint is the most common wall decoration material at present. In concrete construction, it can be painted, rolled or sprayed. For interior decoration of a room, general latex paint needs to be coated twice or more to qualify. If the workers are not serious or perfunctory during the construction, there will often be color differences, especially with darker emulsion paints.
Experts advise: Before the use of latex paint to add a certain amount of water, deployment of a good latex paint to run out. Paints of the same color are also best painted once. If the wall needs to be repaired after construction, the whole wall should be repainted again.
Means two: sewage pipeline
Steal workers index: ★ ★
Phenomenon: A friend who has had construction experience, has encountered such a situation: the construction is completed, on the surface it seems that there is no problem in the renovation project, in full compliance with their own requirements, but once the acceptance is completed, but found the kitchen and bathroom Poor water? In fact, this is caused by the construction team cutting corners in the project. In order to save time and money, a few construction teams may pour concrete blocks containing a lot of cement and sand directly into the sewers. This will cause poor drainage pipes in the future. problem.
The expert reminds: We must strictly supervise and remind the construction team in advance that we cannot use the sewer as garbage road. After the construction of the waterway is completed, all the basins, basins and bathtubs are filled with water to see if the water is unobstructed and if there is any leakage of the pipeline. After all these steps have been completed, acceptance can be considered.
Means three: wire connector
Steal workers index: ★ ★ ☆
Phenomenon: This is also a very stealthy jerry, usually after the completion of the renovation, after the completion of the renovation, consumers in the use of electrical appliances, especially some of the more power-hungry water heaters, air conditioners, etc., switch, socket fever Even burned, some inexperienced consumers often think that this is caused by high-power electrical appliances. Actually, this is not the case. In such a situation, it is very likely that electricians do not follow construction requirements when installing sockets, switches and lamps. Caused by wiring.
Experts remind that summer is coming again, and the use of high-power electrical appliances such as air conditioners is inevitable. Therefore, construction must be supervised by electricians in strict accordance with the operating procedures. After all switches and sockets are installed, it is necessary to carry out the actual work. The use of these parts to see if there is fever, in order to prevent the subsequent use of electrical appliances in the process of causing unnecessary losses.
Means four: wall tile paving
Steal workers index: ★ ★ ★
Phenomenon: Paving tiles is a technical job. If the workers cut corners, it is easy to see problems such as hollowing of the tiles and misalignment of the joints. This will not only reduce the overall aesthetics of the home, but also cause the tiles to crack and crush. In addition, there are also particular concerns about cements and adhesives used for paving tiles. If the mix ratio is unreasonable, there are problems such as falling off.
Experts advise: Wall tiles should be flat and solid, clear patterns, no dirt and grime marks, the surface color is basically the same, uniform joints, plates without cracks, drop angles and lack of edges, the local hollowing shall not exceed 5% of the total.
Means 5: Wall ticking
Steal workers index: ★ ★ ★ ☆
Phenomenon: Today's home renovations generally choose to bury underground pipelines in order to maintain the simplicity and safety of the living environment. To bury underground pipelines, it is necessary to grooving walls and floors before embedding. A few workers perform barbaric construction during slotting operations, which will not only damage the building load-bearing structures, but also cause damage to other nearby pipelines.
Experts advise: Before construction, we must reconfirm the direction and location of the pipeline with the construction team leader. For different wall structures, the requirements for slotting are not the same: the walls of the load-bearing wall in the house are not allowed to be slotted, and the wall with the insulating layer is easy to cause cracking on the surface after being slotted, and on the ground Slotting, but also be careful not to damage the floor, causing trouble to the residents downstairs.
Means six: seam modification
Steal workers index: ★★★★
Phenomenon: In places where walls meet doors and windows, and where two different colors of paint are docked, it is not easy to be noticed. Therefore, these places are exactly what the workers often perfunctory. You often see mixed paints between latex paint and wood, and various problems at the joints.
Experts advise: The treatment of joints is very important, you must supervise the workers to seriously construct. If there are two colors of paint on the wall facing each other, it is necessary to apply adhesive tape on the edge of the first color during construction, and then apply another color of paint on it, so that the construction is completed. After tearing off the tape, the entire seam can be very neat.
Means seven: wire wear tube
Steal workers index: ★★★★☆
Phenomenon: In home renovation construction, almost all the wires are worn in PVC pipes and buried in the walls. Therefore, after the electric wires were put into the PVC pipes, consumers couldn't see them at all, and they could not pass the inspection and acceptance. If the worker is not careful in the operation, it will cause the wire to kink in the tube, causing electricity hazards. If workers deliberately cut corners, they will use wires with joints or put several wires in the same PVC pipe. If problems occur, it will be difficult to replace them.
Experts advise: Consumers are advised to purchase their own wires, then supervise workers' operations at the site, and conduct power-on tests after installation. In addition, consumers must allow the decoration company to leave a "pipeline map." When the electrician had just buried the wires in the wall, he could number the walls and draw a floor plan. Then he used the strokes to draw the direction of the wires and the specific location of the wires, indicating the position on the floor, the ground and the adjacent wall. In particular, the position of the joints of the pipelines should be marked so that in the event of a fault, the line position can be found immediately.
Means eight: facet processing
Steal workers index: ★★★★☆
Phenomenon: The so-called “small face†is a small place that some consumers can't see but does not pay much attention to, such as the upper edge of the door, the underside of the window sill, and so on. Some workers here will cut corners and materials, or even not. Do any processing.
Experts advise: Always keep in mind that there are 6 planes for any object. Don't ignore any details when checking the quality of the project.
Means 9: Ground Leveling
Steal workers index: ★★★★★
Phenomenon: In some projects where there is a suspicion of cutting corners, it is often found that there is a phenomenon of tilting at the edge of the wooden floor of the home, especially near the corners of the wall. What causes this problem? An important reason for wood floor tilting is due to problems with floor leveling before laying. Because some houses are not well-grounded, they need to be re-leveled before laying the floor. If the workers are not careful or deliberately rigged, it will cause “more and more inconveniencesâ€, posing a hidden danger to the floor tilting in the future.
Experts advise: Before ground leveling, ground surface treatment must be done first, and then use cement mortar to level the ground. After the cement is dry, determine the flatness of the entire floor using a dedicated level ruler, and then proceed to the next step.
Means 10: Substrate Treatment
Steal workers index: ★★★★★
Phenomenon: Before painting latex paint and paving the wall and floor tiles, we must do a good job on the surface treatment of the wall or the ground. For the new house, the substrate treatment generally only needs to be polished with coarse sandpaper, and it is not necessary to eradicate the original paint layer. However, the walls of ordinary old houses need to be removed before the next process can be carried out. Some workers, due to the lack of knowledge of the householder about the knowledge in this area, are cutting corners in this area during construction. The consequences of this situation are that unevenness of the wall is caused, there is a color difference after the paint is applied, and the emulsion paint is discolored. Cracks or even peeling, or tiles stuck loosely.
Experts advise: In the construction of paving tiles, you should pay attention to the fact that ceramic tiles cannot be laid directly on the surface of lime mortar, lime paste, lime plaster, hemp plaster and latex paint. Can be laid. Bonding pastes used between tiles and substrates should be formulated in strict accordance with the construction standards and proportions, using the specified grades of cement and adhesive materials, and they cannot be randomly deployed. When applying latex paint, you must pay attention to whether the shading of the wall putty is even and smooth, whether the sanding and rolling are in place. In addition, you should pay attention to whether the latex paint is properly proportioned and whether there is excessive water.
Three trees Lacquer Tiles Lacquer paints Lacquer paints Cement electrical floor tiles Doors Doors Tiles for bathroom Colors for bathroom Tiles for bathroom Whole bathroom Doors for bathroom Bathroom tiles Ceramic tile Floor tiles Kitchen tiles
Composite Wall Cladding,Composite Cladding ,Aluminium Cladding ,Aluminium Composite Panel
Wood Plastic Composite Flooring Co., Ltd. , http://www.china-wpc-decking.com