[
Pacific Security Network News ]
According to my years of experience, we must first understand the definition, minimum illumination, signal to noise ratio, automatic gain control (AGC), backlight compensation (BLC), electronic shutter (ES), white balance (WB) when selecting a camera. And the eight performance indicators of the synchronization method determine the quality of the camera.
1. Clarity: This is the maximum number of lines that can be seen on the monitor (which should be higher than the resolution of the camera) when the camera appears black and white fine lines during shooting. When this number of lines is exceeded, only a gray piece of the screen can be seen on the screen and no black and white lines can be recognized. The sharpness is determined by the number of pixels of the imaging device. Obviously, the more pixels of the imaging device, the clearer the resulting image, and vice versa. The higher the resolution, the higher the camera grade, and vice versa.
2. Signal to noise ratio: is the ratio of signal voltage to noise voltage, usually expressed by the symbol S / N. When the camera captures a brighter scene, the screen displayed by the monitor is usually brighter, and the observer is not easy to see the interference noise in the picture; when the camera takes a darker scene, the screen displayed by the monitor is dim, the observer is It is easy to see the snowflake interference noise in the picture. The strength of the interference noise (that is, the degree of influence of the interference noise on the picture) is directly related to the quality of the camera signal-to-noise ratio indicator. The higher the signal-to-noise ratio of the camera, the smaller the influence of the interference noise on the picture. The typical value of the CCD camera signal-to-noise ratio is generally 45dB~55dB. When measuring the signal-to-noise ratio parameter, it should be directly connected to the video output terminal of the camera using a video clutter.
3. Electronic Shutter (ES): A term used to compare the mechanical shutter function of a camera, which is equivalent to controlling the photographic time of the CCD image sensor. Since the essence of CCD sensation is the accumulation of signal charge, the longer the sensitization time, the longer the accumulation time of the signal charge, and the larger the amplitude of the output signal current. By adjusting the accumulation time of the photogenerated signal charge (ie, adjusting the width of the clock pulse), the function of controlling the CCD sensing time can be realized.
4. Automatic Gain Control (AGC): Use the camera's automatic gain control (AGC) circuit to detect the level of the video signal, and switch the AGC in time, so that the camera can work in a large illumination range. That is, the dynamic range, that is, the sensitivity of the camera is automatically increased in low illumination, thereby increasing the intensity of the image signal to obtain a clear image. Cameras with AGC function will have higher sensitivity in low illumination, but the noise will be more obvious at this time.
5. Synchronization mode: The synchronization mode of the camera generally has internal synchronization, power synchronization and external synchronization. External synchronization (EXT) uses a synchronization signal generated by an external synchronization signal generator to be sent to the external synchronization input of the camera for synchronization. The synchronization signal may be a color composite video or a black burst signal (VBS), a black and white composite video or a composite sync signal (VS), or a multiplexed vertical drive signal (VD2) and a composite video output signal of an external device such as a matrix. Internal synchronization (INT) is performed by generating a synchronization signal using a crystal oscillation circuit inside the camera. LS (Line Locked), also known as linear lock or line lock, uses the camera's AC power to complete the vertical push sync, that is, the camera and power neutral synchronization.
6. White balance (WB): Turn off the automatic white balance. Adjust the red or blue adjustment device manually to change the red or blue condition. Generally, the level can be adjusted up to 107. If you increase or decrease the red level, increase the level. Or reduce each level of blue. In addition to the second, some cameras also have white balance fixed at 3200K (incandescent level) and 5500K (daylight level) and other grade commands. However, it should be known that it is only used in color cameras. Its purpose is to realize that the camera image can accurately reflect the scene condition, and there are two methods: manual white balance and automatic white balance.
7. Backlight Compensation (BLC): When the backlight compensation function is introduced, the camera detects only one sub-area of ​​the entire field of view (such as the center area from the 80th line to the 200th line), and obtains the average signal power of the area. Flat to determine the working point of the AGC circuit. Since the average level of the sub-area is very low, the AGC amplifier has a higher gain, which increases the amplitude of the output video signal, thereby making the subject picture on the monitor clear. At this time, the background image will be brighter, but the difference in subjective brightness from the main picture will be greatly reduced, and the visibility of the entire field of view will be improved.
8. Minimum illumination: The minimum illumination of a typical color camera is 2~3 LUX. The measurement of illumination is based on a certain lens aperture factor. Therefore, you can not only see the minimum illumination indicated in the camera manual, but the camera should be at the same aperture factor. The size of its illuminance value. The minimum illumination is the brightness value of the scene when the brightness of the subject is low to a certain extent and the video signal level output by the camera is lowered to a certain value. The lower the minimum illumination, the higher the camera grade. In actual use, the camera's nominal minimum illumination cannot be used as a measure of the ambient illumination of the site.
Disclaimer: All works that indicate the source of this website are copyrighted or entitled to use by this website. Welcome to reprint and indicate the source. Non-this works are all from the Internet, and the purpose of reprinting is to transmit more information. It does not mean that this website agrees with its views and is responsible for its authenticity.
Other Door Accessories
Sectional Door Accessories: motor 220V-380V, control box, spring break device, cable break device , aluminum alloy rope pulley, enhanced shaft bracket, air bag system, duplex enhanced guide wheel bracket.
Detail introduction for above main accessories
1.Motor and controller:
The garage door operator is designed for residential overhead sectional and tilt doors.
The operator memorizes the limit positions and unique braking system that slows the unit down at the end of its travel.
Rolling code remote control with max. 20 pcs hand transmitters.
The operator is equipped with a manual release lever which allows manual operation of the door in case of power failure.
The controller has a security LOCK function which prevents operation of the door from transmitter.
2.spring break device:
Sectional doors are hinged and they bend in the tracks as the door opens and closes. Many of these doors are counterbalanced with extension springs, also designated "stretch springs," and they have seven characteristics. The length is the measurement of all the coils pressed together. This, along with the inside diameter of the coils and wire size - the thickness of the wire from which the springs are made - determine the stretch, the distance the spring is extended - normally half the door height, and pull, the force the spring pulls when stretched its normal length. The type of ends determine how the ends of the spring are mounted. The initial tension is the percentage of pull needed to separate the coils. This is determined by the pitch with which the springs are wound. On sectional garage door springs this is normally 15 percent. For example a 100 pound pull spring requires 15 pounds of weight to separate the coils; when a door is open the two springs will support 15 pounds of door weight without any stretch.
Most extension springs are made of oil tempered wire. These are normally coated or painted. Some springs are made of galvanized wire.
3.able break device:
cable break device ,door hardware
adjustable bottom bracket .
the raw material hot plate
zinc plated
safety device
adjustable bottom bracket
the raw material hot plate
zinc plating
spring safety device ,2" and 3" safety device
once the cable is broken ,this devoice can keep the hurt away from the door falling
4.aluminum alloy rope pulley
Equipment: CNC stamping/punching machine, CNC bending machine, CNC cutting
machine, 5~250 tons punching machines, welding machine, polish machines...
Processed material: stainless steel: copper, carbon steel
Surface treatment: Hot galvanized, polishing
Making process:Stamping, deep drawing,bending, punching, laser cutting,threading,
welding, tapping, riveting, grinding
5.air bag system
It is a safety device. When the door is down to hit something, it will up automatically.
Operation pressure:<3mbar
Battery:CR2032*2
Battery lifetime>1 year
Emission frequency: 315MHZ
Emission power:<10mW
Receiver power source:12V
6.duplex enhanced guide wheel bracket
Determining the right type of sectional door roller for your garage door tracks can be a little confusing, especially when you do not know what you need to look for in a garage door roller. To simplify things, there are two primary things you need to be aware of. First are the actual dimensions of the roller, and second is purpose that you will be using the door for. You can read below about measuring your roller and choosing the right quality of material for your door.
Other Door Accessories,Electronic Door Accessories,Automatic Door Accessories,High Speed Door Radar Detector
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hfgaragedoor.com