Composite flooring is favored by more and more consumers for its natural appearance and excellent performance, but the composite flooring will have some problems in the process of use, such as floor cracking, floor lifting, floor inequality. Wait, once these problems occur, it is quite troublesome. Don't worry, Jiuzheng Building Materials Network has collected the four major problems and solutions for the composite floor. Let's take a look.
Composite floor installation problem one, there is an empty drum
The most common problem with laminate flooring during installation is the sound of an empty drum, and the floor is not firmly attached to the ground. The reason for such problems is mostly due to the fact that the fixing is not true, mainly because the number of nails and keels, the board and the floor nails are small or the nails are not strong, and sometimes the shrinkage or the glue is unqualified due to the change of the moisture content of the sheet. Caused by.
Treatment plan: When installing, try to avoid this phenomenon, and only strictly test the moisture content of the floor, the quality of the adhesive and the accessories. Only when all the products are fully inspected can they be used; the installation parts such as nails during the installation process Can not be short and two.
Composite floor installation problem 2, uneven
After the floor was installed, although there was no loud sound, the surface was uneven. The main reason for this phenomenon is that the base layer is not flat or the floor itself is deformed.
Treatment plan: To avoid this phenomenon, only use the level to level the surface of the keel during construction. If the unevenness should be adjusted, the keel should be made of ventilation slots, and the edge of the board should be 10 mm. Ventilation gap; the insulation layer material must be dry to prevent the board from getting up after damp.
Composite floor installation problem three, lifting
After the composite floor is installed, the composite floor is partially lifted. The partial lifting of the composite floor must be caused by moisture, and there are two reasons for the moisture. One reason is that there is a hidden danger in the moisture treatment; the other reason is that the seam is too small or seamless, and the water pipe is leaking during use. Caused by soaking the floor.
Treatment method: After paving, the paint should be complete when the floor is painted; avoid the daily water immersion into the lower part of the floor and cause the floor to expand. Instantly use a rag or dry mop to clean the floor surface water.
Composite floor installation problem four, the seam is not strict
After installation, it was found that the seams were not strict. There are two main reasons for this phenomenon:
1) The operation of the construction personnel is not standardized;
2) The width of the composite floor has large error and poor processing quality.
Treatment plan: If it is the first reason, you only need to require the construction personnel to standardize the operation or replace the construction personnel; if it is the second reason, fill the joints with fillers or buy a composite floor.
In addition, the following matters should be noted in the installation of composite flooring:
1. Before installing the composite floor, it should be determined that the base layer should be flat, firm, dry, clean, non-polluting, and the strength meets the design requirements.
2. When installing the composite floor, the indoor temperature should comply with the requirements of the product description.
3, under the composite floor should be full of moisture-proof floor mats, paving flat, seams must not be stacked, and fixed with tape.
4. When installing the first row of composite flooring, the groove should face the wall, and a gap of about 10 mm should be left between the floor and the wall.
5. When the length or width of the room exceeds 8 meters, it is necessary to set the expansion joint and install the flat pressure strip.
6, the wooden kicking foot is tightly bonded with a 45 degree groove, the height and thickness of the wall are the same, the nail cap is not exposed, and the nail eye is covered.
7. After the composite floor is installed, it should ensure that the surface is straight, the color and wood grain are consistent, and there is no glue mark.
After the composite floor is installed, it is necessary to master the method of maintenance of the composite floor, so as to extend the service life of the composite floor and ensure that the composite floor is still as new.
China Manufacturer of Transparent Led Screen,Led Glass Screen,Transparent Led Display,Transparent Led Glass Screen,best choice for display advertisement for curtain wall,shopping mall
Transparent Led Screen,Led Glass Screen,Transparent Led Display,Transparent Led Glass Screen
Shenzhen YuGuang New Material Co.,Ltd , https://www.ygsmartfilm.com