Failure analysis
Plastic extruder is a common plastic machinery equipment "target=_blank> mechanical equipment, in the process of daily operation of the extruder, the extrusion machine has a variety of failures, affecting the normal production of plastic machinery, below we will Analysis of extruder failures.
Host power " target=_blank> machine current is unstable
1. Production reasons:
(1) Feeding is uneven.
(2) The main motor bearing is damaged or poorly lubricated.
(3) A certain heater fails and does not heat up.
(4) The screw adjustment pad is incorrect, or the phase is wrong, and the components interfere.
2, the processing method:
(1) Check the feeder to troubleshoot.
(2) Repair the main motor and replace the bearing if necessary.
(3) Check that each heater is working properly and replace the heater if necessary.
(4) Check the adjustment pad and pull out the screw to check whether the screw has interference.
Main motor cannot start
1, the cause:
(1) The driving procedure is wrong.
(2) There is a problem with the main motor thread, and the fuse is burned.
(3) The interlocking device associated with the main motor functions
2, the processing method:
(1) Check the procedure and drive again in the correct driving order.
(2) Check the main motor power "target=_blank> machine circuit.
(3) Check if the lubricating oil pump is started and check the status of the interlocking device related to the main motor. The oil pump does not turn on and the motor cannot be turned on.
(4) After the inverter's induction power is not discharged, turn off the main power and wait for 5 minutes before starting.
(5) Check if the emergency button is reset.
The machine head is not well discharged or blocked
1, the cause:
(1) A certain section of the heater does not work, and the material is not plasticized.
(2) The operating temperature setting is low, or the molecular weight distribution of the plastic is wide and unstable.
(3) There may be foreign matter that is not easily melted.
2, the processing method:
(1) Check the heater and replace if necessary.
(2) Verify the set temperature of each section and, if necessary, negotiate with the technician to increase the temperature setting.
(3) Clean and inspect the extrusion system and the machine head.
Main electric starting current is too high
1, the cause:
(1) The heating time is insufficient and the torque is large.
(2) A certain heater does not work.
2, the processing method:
(1) Apply the hand truck when driving. If it is not easy, extend the heating time or check whether the heaters are working properly.
The main motor makes an abnormal sound
1, the cause:
(1) The main motor bearing is damaged.
(2) A thyristor in the main motor thyristor rectifier circuit is damaged.
2, the processing method:
(1) Replace the main motor bearing.
(2) Check the thyristor rectifier circuit and replace the thyristor component if necessary.
Plastic extruders undergo three stages of extrusion in plastics, namely plasticizing, forming and cooling the raw materials. Plastic extruders are also divided into many different types. Screw extruders are divided into single-screw extruders, twin-screw extruders, multi-screw extruders, etc.; extruders can be divided into continuous extrusions according to their functions. And discontinuous extrusion. The output of the extruder is determined by the rotational speed of the screw. The screw speed can affect the output of the extruded plastic of the extruder, and can also affect the plasticizing effect.
(This article Source: Plastic Extruder http:// )
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
BOHONG also manufactures PDC dome, conical and chisel cutters. These can be used as impact arrestors for PDC Drill Bits.As cutting structures for roller cone drill bits and down hole hammer/percussion bits, and as gage protection for all drill bits and other downhole tools such as stabilizers, reamers, hole-openers, etc.
Diamond Grinding shoes double bar trapezoidal tool - two abrasive segments are evenly embedded in the metal through a fine manufacturing process.It has strong scraping ability , high durability and long service life.
-Metal substrate can meet dry/wet applications.
-Commonly used for floor grinding.
Metal Bond Trapezoidal Diamond Grinding Shoe Oval - Provides great grinding power. Two oval shaped abrasives are uniform in texture, increasing tool life and performance.
-Allows for special scraping needs and increased durability.
Applications:
Applications include a variety of high, medium and low cables, steel cord , medical wire, superconducting wire , stranding and spring wire. Using different types of dies for the same type of wire can show different results in terms of die wear and usage time.
BOHONG offers a customized consultation service to provide customers with the most suitable Wire Drawing dies with guaranteed work efficiency.
Polycrystalline Diamond Pdc Cutter,Polycrystalline Diamond Compos,Pdc Shoes For Grinding Floor,Grinding Plates For Concrete Grinding
Henan Bohong New Material Co., Ltd , https://www.bohongpcd.com