Sinking of defects in injection molding products

Gate dizziness, also known as sun spots, fog spots, that is, the circular color change produced near the gate. The shape is an ellipse or a circle, usually determined by the method of pouring and the size of the gate, due to melt fracture.
Defect mechanism
There are many reasons for creating a sprue, the main reasons are:
The barrel, nozzle and mold temperature are low;
The injection pressure is too high and the mold temperature is too low. If the mold temperature is too low, the plastic will cool too quickly, causing too much cold material, and then rushing to the surface of the product, resulting in defects;
The gate setting is unbalanced; the gate is too small or the cavity at the pouring is too thin. When the glue flow is large and the cross-sectional area is small (gate, cavity thickness), the shear rate is large, the shear stress increases, and the molten rubber is broken to cause the gate halo phenomenon. Cracking of the melt can also cause other defects such as flow marks, discoloration, and fog.
Final solution:

forming

Process

➤ Reduce injection speed, injection pressure, multi-stage injection pressure and position exchange;

➤ Increase the melt temperature and mold temperature to improve the fluidity of the material during the filling process.

Mold

➤Adjust the gate position so that the gate does not affect the appearance quality of the product as much as possible;

➤Appropriate gate section, the gate and runner section are preferably rounded to reduce the flow resistance of the stream;

➤With the appropriate gate type, the side-injection and lap-type infusion effects are better than the latent pouring effect;

➤ reasonable arrangement of cold wells;

simulation

analysis

➤The numerical simulation can be used to predict the temperature, shear rate and shear stress of the melt passing through the above narrow zone. According to the analysis results, the corresponding adjustment can be made, and the appropriate gate size and cavity wall thickness at the glue can be found very quickly.

With WiFi doorbell, can monitor home anytime, anywhere from your mobile phone, tablet. You can see, hear and speak to vistors from anywhere and remote open door for visitors if need. Built-in PIR and night vision, never miss a visitor.

WiFi doorbell Functions


Advantage:

Only have one outdoor device, receiver is your smart phone 
support both ios and Android devices 
clear voice & image
take photo and video 
Outdoor device can connect to internet by both wifi and internet cable 



Description

  • Your mobile phone can intercom with the doorbell by connect to wifi or 3G/4G
  • 1 camera can suppport 8 pcs smart phone at most 
  • Camera is CMOS 
  • With rainproof cover 
  • Remote unlock the electornic lock 
  • alarm function 
  • connect to power by adapter 
  • Hand free intercom
  • Night vision with 6IR lights in the camera



Specifications

Launch date: 2014, Aug
Camera:  1/4''/F2.4/110 degree
Distinguished:  420 line
Illumination: 2LUX
Light source:  6pcs infrared light 
Power Standby: DC 12V 1A
Power dissipation Standby: working, 3.8W
Dimensions: 160*97*40mm
Material: ABS
Power input: 12V 1A
Lock output: 12V
Operating temperature: Subzero 10 degree to +55 degree
Operating Humidity:  10-90%
WIFI standard: IEEE802.11b/g/n
WIFI mode: DSSS/CCK 11Mbps
Channel Frequency: 2412~2484MHZ
RX sensitivity:  Negative 85 dBm
TX power: 16 dBm
EVM: Negative 22 dBm
Sensor size: 1/4''
Sensor pixel:  0.3M
Lens angle: 110 degree
Aperture: F2.0mm
Night vision:  6*940NM IR LED

wifi doorbell

Smart Home WiFi Doorbell

Smart Home Wifi Doorbell,Smart Home Automation Wifi Doorbell,Smart Video Doorbell Intercom

Shenzhen Zhuohao Intelligent Electronic Development Co., Ltd. , https://www.szactop-smart.com